// fading transitions sketch for 6-tube IN-17 board with default connections.
// based on 6-tube sketch by Emblazed
// 
// 02/27/2013 - modded for six bulb board, updated flicker fix by Brad L

// SN74141 : Truth Table
//D C B A #
//L,L,L,L 0
//L,L,L,H 1
//L,L,H,L 2
//L,L,H,H 3
//L,H,L,L 4
//L,H,L,H 5
//L,H,H,L 6
//L,H,H,H 7
//H,L,L,L 8
//H,L,L,H 9

// SN74141 (1)
int ledPin_0_a = 2;                
int ledPin_0_b = 3;
int ledPin_0_c = 4;
int ledPin_0_d = 5;

// SN74141 (2)
int ledPin_1_a = 6;                
int ledPin_1_b = 7;
int ledPin_1_c = 8;
int ledPin_1_d = 9;

// anode pins
int ledPin_a_1 = 10;
int ledPin_a_2 = 11;
int ledPin_a_3 = 12;
int ledPin_a_4 = 13;

void setup() 
{
  pinMode(ledPin_0_a, OUTPUT);      
  pinMode(ledPin_0_b, OUTPUT);      
  pinMode(ledPin_0_c, OUTPUT);      
  pinMode(ledPin_0_d, OUTPUT);    
  
  pinMode(ledPin_1_a, OUTPUT);      
  pinMode(ledPin_1_b, OUTPUT);      
  pinMode(ledPin_1_c, OUTPUT);      
  pinMode(ledPin_1_d, OUTPUT);      
  
  pinMode(ledPin_a_1, OUTPUT);      
  pinMode(ledPin_a_2, OUTPUT);      
  pinMode(ledPin_a_3, OUTPUT);     
 
  // NOTE: Grounding on virtual pins 14 and 15 (analog pins 0 and 1) will set the Hour and Mins.
  
  pinMode( 14, INPUT ); // set the virtual pin 14 (pin 0 on the analog inputs ) 
  digitalWrite(14, HIGH); // set pin 14 as a pull up resistor.

  pinMode( 15, INPUT ); // set the virtual pin 15 (pin 1 on the analog inputs ) 
  digitalWrite(15, HIGH); // set pin 15 as a pull up resistor.
 
}

void SetSN74141Chips( int num2, int num1 )
{
  int a,b,c,d;
  
  // set defaults.
  a=0;b=0;c=0;d=0; // will display a zero.
  
  // Load the a,b,c,d.. to send to the SN74141 IC (1)
  switch( num1 )
  {
    case 0: a=0;b=0;c=0;d=0;break;
    case 1: a=1;b=0;c=0;d=0;break;
    case 2: a=0;b=1;c=0;d=0;break;
    case 3: a=1;b=1;c=0;d=0;break;
    case 4: a=0;b=0;c=1;d=0;break;
    case 5: a=1;b=0;c=1;d=0;break;
    case 6: a=0;b=1;c=1;d=0;break;
    case 7: a=1;b=1;c=1;d=0;break;
    case 8: a=0;b=0;c=0;d=1;break;
    case 9: a=1;b=0;c=0;d=1;break;
    default: a=1;b=1;c=1;d=1;
    break;
  }  
  
  // Write to output pins.
  digitalWrite(ledPin_0_d, d);
  digitalWrite(ledPin_0_c, c);
  digitalWrite(ledPin_0_b, b);
  digitalWrite(ledPin_0_a, a);

  // Load the a,b,c,d.. to send to the SN74141 IC (2)
  switch( num2 )
  {
    case 0: a=0;b=0;c=0;d=0;break;
    case 1: a=1;b=0;c=0;d=0;break;
    case 2: a=0;b=1;c=0;d=0;break;
    case 3: a=1;b=1;c=0;d=0;break;
    case 4: a=0;b=0;c=1;d=0;break;
    case 5: a=1;b=0;c=1;d=0;break;
    case 6: a=0;b=1;c=1;d=0;break;
    case 7: a=1;b=1;c=1;d=0;break;
    case 8: a=0;b=0;c=0;d=1;break;
    case 9: a=1;b=0;c=0;d=1;break;
    default: a=1;b=1;c=1;d=1;
    break;
  }
  
  // Write to output pins
  digitalWrite(ledPin_1_d, d);
  digitalWrite(ledPin_1_c, c);
  digitalWrite(ledPin_1_b, b);
  digitalWrite(ledPin_1_a, a);
}


float fadeMax = 5.0f;
float fadeStep = 1.0f;
int NumberArray[6]={0,0,0,0,0,0};
int currNumberArray[6]={0,0,0,0,0,0};
float NumberArrayFadeInValue[6]={0.0f,0.0f,0.0f,0.0f,0.0f,0.0f};
float NumberArrayFadeOutValue[6]={8.0f,8.0f,8.0f,8.0f,8.0f,8.0f};

void DisplayFadeNumberString()
{
 
  // Anode channel 1 - numerals 0,3
  SetSN74141Chips(currNumberArray[0],currNumberArray[3]);   
  digitalWrite(ledPin_a_2, HIGH);   
  delay(NumberArrayFadeOutValue[0]);
  SetSN74141Chips(NumberArray[0],NumberArray[3]);   
  delay(NumberArrayFadeInValue[0]);
  digitalWrite(ledPin_a_2, LOW);
  
  // Anode channel 2 - numerals 1,4
  SetSN74141Chips(currNumberArray[1],currNumberArray[4]);   
  digitalWrite(ledPin_a_3, HIGH);   
  delay(NumberArrayFadeOutValue[1]);
  SetSN74141Chips(NumberArray[1],NumberArray[4]);   
  delay(NumberArrayFadeInValue[1]);
  digitalWrite(ledPin_a_3, LOW);
  
   // Anode channel 3 - numerals 2,5
  SetSN74141Chips(currNumberArray[2],currNumberArray[5]);   
  digitalWrite(ledPin_a_4, HIGH);   
  delay(NumberArrayFadeOutValue[2]);
  SetSN74141Chips(NumberArray[2],NumberArray[5]);   
  delay(NumberArrayFadeInValue[2]);
  digitalWrite(ledPin_a_4, LOW);
  
  // Loop thru and update all the arrays, and fades.
  for( int i = 0 ; i < 6 ; i ++ )
  {
    if( NumberArray[i] != currNumberArray[i] )
    {
      NumberArrayFadeInValue[i] += fadeStep;
      NumberArrayFadeOutValue[i] -= fadeStep;
  
      if( NumberArrayFadeInValue[i] >= fadeMax )
      {
        NumberArrayFadeInValue[i] = 0.0f;
        NumberArrayFadeOutValue[i] = fadeMax;
        currNumberArray[i] = NumberArray[i];
      }
    }
  }  
}

// Defines
long MINS = 60;         // 60 Seconds in a Min.
long HOURS = 60 * MINS; // 60 Mins in an hour.
long DAYS = 12 * HOURS; // 24 Hours in a day. > Note: change the 24 to a 12 for non military time.

long runTime = 0;       // Time from when we started.

// default time sets. clock will start at 12:34:00.  This is so we can count the correct order of tubes.
long clockHourSet = 12;
long clockMinSet  = 34;

int HourButtonPressed = false;
int MinButtonPressed = false;

////////////////////////////////////////////////////////////////////////
//
//
////////////////////////////////////////////////////////////////////////
void loop()     
{
  // Get milliseconds.
  runTime = millis();
  
  int hourInput = digitalRead(14);  
  int minInput  = digitalRead(15);

  if( hourInput == 0 )
    HourButtonPressed = true;
  if( minInput == 0 )
    MinButtonPressed = true;
  
  if( HourButtonPressed == true && hourInput == 1 )
  {
    clockHourSet++;
    HourButtonPressed = false;
  }
  
  if( MinButtonPressed == true && minInput == 1 )
  {
    clockMinSet++;
    MinButtonPressed = false;
  }

  // Get time in seconds.
  long time = (runTime) / 1000; //////////change this value to speed up or slow down the clock, set to smaller number such as 10, 1, or 100 for debugging
  
  // Set time based on offset..
  // long hbump = 60*60*clockHourSet;
  long hbump = 60*60*clockHourSet;
  long mbump = 60*clockMinSet;
  time += mbump + hbump;

  // Convert time to days,hours,mins,seconds
  long days  = time / DAYS;    time -= days  * DAYS; 
  long hours = time / HOURS;   time -= hours * HOURS; 
  long minutes  = time / MINS;    time -= minutes  * MINS; 
  long seconds  = time; 

  // Get the high and low order values for hours,min,seconds. 
  int lowerHours = hours % 10;
  int upperHours = hours - lowerHours;
  int lowerMins = minutes % 10;
  int upperMins = minutes - lowerMins;
  int lowerSeconds = seconds % 10;
  int upperSeconds = seconds - lowerSeconds;
  if( upperSeconds >= 10 )   upperSeconds = upperSeconds / 10;
  if( upperMins >= 10 )      upperMins = upperMins / 10;
  if( upperHours >= 10 )     upperHours = upperHours / 10;
  
  if( upperHours == 0 && lowerHours == 0 )
  {
    upperHours = 1;
    lowerHours = 2;
  }

  // Fill in the Number array used to display on the tubes.
  NumberArray[1] = lowerHours; 
  NumberArray[2] = lowerMins;
  NumberArray[3] = upperMins;
  NumberArray[4] = upperSeconds;  
  NumberArray[5] = upperHours;
  NumberArray[0] = lowerSeconds;//



  // Display.
  DisplayFadeNumberString();
}